web-u2
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
web-u2 [2019/09/09 09:00] – fix overview kingkevin | web-u2 [2019/09/09 13:48] – [WITRN U2 104083] kingkevin | ||
---|---|---|---|
Line 1: | Line 1: | ||
The U2 is a USB power meter and tester. | The U2 is a USB power meter and tester. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | ===== Overview ===== | ||
+ | |||
+ | ==== Features ==== | ||
It is full of features and makes it the most complete USB power meter I known of: | It is full of features and makes it the most complete USB power meter I known of: | ||
Line 6: | Line 13: | ||
* large (1.77 in / 4.5 cm) clear (can use large fonts) LCD screen (160*128 pixels) | * large (1.77 in / 4.5 cm) clear (can use large fonts) LCD screen (160*128 pixels) | ||
* can detect charger compliance/ | * can detect charger compliance/ | ||
- | * external power input: to not affect the current measurement, | + | * external power input: to not affect the current measurement, |
* computer interface to read the measured values: USB HIB (micro-USB port which also can externally power the device), and Bluetooth (U2p version) | * computer interface to read the measured values: USB HIB (micro-USB port which also can externally power the device), and Bluetooth (U2p version) | ||
+ | ==== Resources ==== | ||
+ | |||
+ | The manufacturer is called **WITRN**. | ||
+ | The device was first called **WEB-U2**, but now they registered the trademark/ | ||
+ | |||
+ | You can buy the [[https:// | ||
+ | The software also points to the probably authorized re-seller [[https:// | ||
+ | The manual warms about the [[https:// | ||
+ | |||
+ | The [[http:// | ||
+ | It only point to the user guide and software (with broken link).\\ | ||
+ | Instead they recommend to follow the QQ group 313755927. | ||
+ | |||
+ | Here links I could gather to get the latest version of: | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | * [[http:// | ||
+ | |||
+ | There is also this thorough [[https:// | ||
===== Hardware ===== | ===== Hardware ===== | ||
- | There are several | + | There are several versions of the hardware. |
- | I will us the names I can read on the device itself to identify them. | + | |
- | ==== WEB-U2 ==== | + | ==== WITRN U2 104083 |
This is the first device I bought from the [[https:// | This is the first device I bought from the [[https:// | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
The original manufacturer blocked this device. | The original manufacturer blocked this device. | ||
Line 26: | Line 56: | ||
This device can still be used to measure voltage and current, but since there is no update anymore it will not be able to be used to detect charger profiles. | This device can still be used to measure voltage and current, but since there is no update anymore it will not be able to be used to detect charger profiles. | ||
+ | There is also a footprint for an Bluetooth adapter behind the screen, but it was not placed yet (the software was probably not ready). | ||
+ | |||
+ | {{: | ||
+ | |||
+ | I read out the FRAM (where the settings are stored) but did not find the serial number in there. | ||
+ | I also cleared it to confirm the serial is not stored in the FRAM, but in the firmware. | ||
+ | Sadly the firmware is read protected. | ||
+ | |||
+ | Debug header pinout: | ||
+ | < | ||
+ | _________ | ||
+ | __|8 6 4 2| | ||
+ | |9 7 5 3 1| | ||
+ | ----------- | ||
+ | </ | ||
+ | |||
+ | |||
+ | - SWDIO (SWD, STM32F072 pin 34/PA13) | ||
+ | - SDA (I²C, with FRAM at 0x50) | ||
+ | - SWCLK (SWD, STM32F072 pin 37/PA14) | ||
+ | - GND | ||
+ | - GND | ||
+ | - VDD | ||
+ | - VDD | ||
+ | - SCL (I²C, with FRAM at 0x50) | ||
+ | - nRST (SWD, STM32F072 pin 7/NRST, you must connect under reset since SWD is disable after boot) | ||
+ | ==== WITRN U2 V2.0 ==== | ||
+ | |||
+ | Because the clone was bricked, I got a genuine replacement. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | A Bluetooth module could be placed on the front side of the bottom board. | ||
+ | The front board could also be light bz LEDs from the back side. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | ==== Qway U2p ==== | ||
+ | |||
+ | The U2p version is a variant of the U2 with 4 button instead of 2, and a switch to enable Power Delivery probing | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | Finally it was also possible to get a version with Bluetooth and some light next to the USB input (not sure when it is on though) | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | ==== Board ==== | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | Here a list of the components present on the Qway U2p V1.1 board: | ||
+ | - input USB 3.0 type A plug | ||
+ | - input USB type C socket | ||
+ | - input USB type micro-B socket | ||
+ | - output USB 3.0 type A socket | ||
+ | - output USB type C socket | ||
+ | - data USB type micro-B socket, USB HID connection to the computer to read the measurements and flash the firmware | ||
+ | - 4 button to interact with the interface (back, ok, previous, next) | ||
+ | - PD switch to enable USB-C Power Delivery triggering | ||
+ | - [[http:// | ||
+ | - input diode protection: not in-line, but shorting GND to VBUS when GND > VBUS | ||
+ | - R012F shunt resistor (12 mOhm): to measure the current | ||
+ | - 5R10 shunt resistor (5.1 Ohm): which can be switched in line to measure low currents | ||
+ | - [[https:// | ||
+ | - [[https:// | ||
+ | - [[https:// | ||
+ | - [[https:// | ||
+ | - [[https:// | ||
+ | - UART pins: to connect to the AT-09 Bluetooth module (with TI CC2541 chip). pinout, beginning with square pin: 3.8V GND RX TX | ||
===== Software ===== | ===== Software ===== | ||
web-u2.txt · Last modified: 2024/01/07 17:49 by 127.0.0.1