Differences

This shows you the differences between two versions of the page.

--- spark_counter [2017/01/18 21:14] – [peacefair PZEM-004] kingkevin
+++ spark_counter [2022/02/10 11:50] – update git links kingkevin
@@ Line 13: / Line 13: @@
 {{:spark_counter:dsc02371.jpg?0x300|complete spark counter}}
-**warning: the electricity meter I am presenting will only work for 1 phase 2 wires power distribution systems. I have a 3 phases 4 wires system and I am doing it wrong.**
+**warning: the electricity meter I am presenting will only work for 1-phase 2-wire power distribution systems. I have a 3-phase 4-wire system and I was doing it wrong. This has been fixed with the [[spark abacus]].**
 ====== peacefair PZEM-004 ======
@@ Line 80: / Line 80: @@
 I removed the pizeo-element to prevent this annoying sound.
-{{:spark_counter:dsc02344.jpg?0x200|PZEM-004 board front}}
+{{:spark_counter:pzem-004-01.jpg?0x200|PZEM-004 board front}}
-{{:spark_counter:dsc02325.jpg?0x200|PZEM-004 board back}}
+{{:spark_counter:pzem-004-02.jpg?0x200|PZEM-004 board back (without buzzer)}}
-{{:spark_counter:dsc02327.jpg?0x200|PZEM-004 board IC}}
 The power meter uses a single chip solution, the [[http://www.sdicmicro.com/products.html?ic=SD3004|SDIC microelectronics SD3004]] ({{:spark_counter:sd3004_datasheet_v0.2c.pdf|datasheet}}).
@@ Line 98: / Line 97: @@
 USART to query the power meter, SPI to communicate with the nRF24L01+, and the nRF24L01+ protocol are implemented in C (using a lot of interrupts).
-The source code is available [[https://git.cuvoodoo.info/spark_counter/|in this git]].
+The source code is available [[https://git.cuvoodoo.info/kingkevin/spark_counter/|in this git]].
 I prefer directly writing in the registers as described in the [[http://www.atmel.com/images/Atmel-8271-8-bit-AVR-Microcontroller-ATmega48A-48PA-88A-88PA-168A-168PA-328-328P_datasheet_Complete.pdf|datasheet]] rather than using an [[https://www.arduino.cc/en/Main/Software|abstract IDE]] and [[https://github.com/TMRh20/RF24|libraries]].
 This way I learn how it works in details.
@@ Line 122: / Line 121: @@
 On the [[#ATmega328P|micro-controller]] side I implemented the complete SPI-based protocol using the [[https://www.nordicsemi.com/eng/content/download/2726/34069/file/nRF24L01P_Product_Specification_1_0.pdf|datasheet]].
-The source code is available [[https://git.cuvoodoo.info/spark_counter/|in this git]].
+The source code is available [[https://git.cuvoodoo.info/kingkevin/spark_counter/|in this git]].
 On the [[#Raspberry Pi|computer]] side I use the [[https://github.com/TMRh20/RF24|RF24 library]].
@@ Line 136: / Line 135: @@
 To receive the measurements I used a [[#nRF24L01+|nRF24L01+ transceiver]] with the [[https://github.com/TMRh20/RF24|RF24 library]].
-The source code is available [[https://git.cuvoodoo.info/spark_counter/|in this git]].
+The source code is available [[https://git.cuvoodoo.info/kingkevin/spark_counter/|in this git]].
 [[http://elinux.org/RPi_Low-level_peripherals#P1_Header|RPi]] - nRF24L01+ connection: