jtag
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | Next revisionBoth sides next revision | ||
jtag [2017/03/30 12:42] – add MB936 kingkevin | jtag [2017/03/30 12:50] – move aluminium kingkevin | ||
---|---|---|---|
Line 73: | Line 73: | ||
For $9 you can't expect more, and if you want a cheap adapter I recommend the other ones (see below). | For $9 you can't expect more, and if you want a cheap adapter I recommend the other ones (see below). | ||
+ | |||
+ | ==== aluminium ==== | ||
+ | |||
+ | This [[http:// | ||
+ | It supports SWD, and SWIM (for STM8), but not JTAG. | ||
+ | They replaced the additional JTAG pins with power pins. | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | STM32F103C8 connection: | ||
+ | ^ STM32F103C8 signal ^ STM32F103C8 pin ^ adapter pin ^ adapter signal ^ | ||
+ | | PB6 | 42 | 1 | RST | | ||
+ | | PB14 | 27 | 2 | SWDIO | | ||
+ | | USB GND | | 3 | GND | | ||
+ | | USB GND | | 4 | GND | | ||
+ | | PB8/PB11 | 45/22 | 5 | SWIM | | ||
+ | | PA5/PB13 | 15/26 | 6 | SWCLK | | ||
+ | | LDO VCC | | 7 | 3.3V | | ||
+ | | LDO VCC | | 8 | 3.3V | | ||
+ | | USB VCC | | 9 | 5V | | ||
+ | | USB VCC | | 10 | 5V | | ||
+ | | PA9 | 30 | current source | ||
==== BAITE ==== | ==== BAITE ==== | ||
Line 101: | Line 126: | ||
the adapter pins are protected with a 220 ohms resistor. | the adapter pins are protected with a 220 ohms resistor. | ||
- | |||
- | ==== aluminium ==== | ||
- | |||
- | This [[http:// | ||
- | It supports SWD, and SWIM (for STM8), but not JTAG. | ||
- | They replaced the additional JTAG pins with power pins. | ||
- | |||
- | {{: | ||
- | {{: | ||
- | {{: | ||
- | {{: | ||
- | |||
- | STM32F103C8 connection: | ||
- | ^ STM32F103C8 signal ^ STM32F103C8 pin ^ adapter pin ^ adapter signal ^ | ||
- | | PB6 | 42 | 1 | RST | | ||
- | | PB14 | 27 | 2 | SWDIO | | ||
- | | USB GND | | 3 | GND | | ||
- | | USB GND | | 4 | GND | | ||
- | | PB8/PB11 | 45/22 | 5 | SWIM | | ||
- | | PA5/PB13 | 15/26 | 6 | SWCLK | | ||
- | | LDO VCC | | 7 | 3.3V | | ||
- | | LDO VCC | | 8 | 3.3V | | ||
- | | USB VCC | | 9 | 5V | | ||
- | | USB VCC | | 10 | 5V | | ||
- | | PA9 | 30 | current source | ||
===== Altera USB-Blaster ===== | ===== Altera USB-Blaster ===== |
jtag.txt · Last modified: 2024/01/07 17:49 by 127.0.0.1