Differences

This shows you the differences between two versions of the page.

--- jtag [2016/01/13 09:26] – [scan chain] kingkevin
+++ jtag [2016/02/03 13:47] – [ST-Link v2 (clone)] add pinout kingkevin
@@ Line 24: / Line 24: @@
 {{:jtag:dsc02406.jpg?0x100|pinout sticker}}
 {{:jtag:st-link_v2_baite.svg?0x100|pinout}}
+^ STM32F103C8 signal ^ STM32F103C8 pin ^ adapter pin ^ adapter signal ^
+| PA7 | 17 | 1 | JRST |
+| AMS1117 |  | 2 | 3V3 |
+| USB VCC |  | 3 | 5V |
+| PA4 | 14 | 4 | JTCK/SWCLK |
+| PB11 | 22 | 5 | SWIM/SWDIO |
+| PA14 | 37 | 6 | JTMS |
+| USB GND |  | 7 | GND |
+| PA5 | 15 | 8 | JTDO |
+| PB6 | 42 | 9 | SWIM_RST |
+| PA6  | 16 | 10 | JTDI |
+| PB12,PB14 | 25,27 |  |  100 ohms |
+| PB5 | 41 |  | LED |
+the adapter pins are protected with a 220 ohms resistor.
   * one [[http://www.aliexpress.com/item/Hot-Sale-1PCS-ST-LINK-Stlink-ST-Link-V2-Mini-STM8-STM32-Simulator-Download-Programmer-Programming/32343514985.html|more generic]]
 {{:jtag:dsc02407.jpg?0x100|device front}}
@@ Line 33: / Line 50: @@
 This is newer variant of JTAG which requires only 2 signal lines instead of 4+.
 But but aware, they both have different pinouts on the connector.
+The second one offers 2 more power ports at the expense of JTAG TDI and TDO/SWO.
-These JTAG adapter are based STM32F1xx ARM Cortex M3 micro-controllers.
+These JTAG adapters are based STM32F1xx ARM Cortex M3 micro-controllers.
 And ironically enough I in turn use them to program and debug STM32F1xx ARM Cortex M3 micro-controllers.
@@ Line 156: / Line 174: @@
 Info : stm32f1x.cpu: hardware has 6 breakpoints, 4 watchpoints
 </code>
+==== SEGGER J-Link (clone) ====
+The [[http://www.aliexpress.com/item/FREE-SHIPPING-V8-ARM-Emulator-supports-ARM7-ARM9-ARM11-Cortex-M3-core-ADS-IAR-STM32-Emulator/32262570128.html|O-Link-ARM V8]] is a [[https://www.segger.com/jlink_base.html|SEGGER J-Link]] clone.
+{{:jtag:imag0403.jpg?0x150|device front}}
+{{:jtag:imag0404.jpg?0x150|device back}}
+{{:jtag:imag0406.jpg?0x150|PCB front}}
+It supports JTAG, SWD, SWO, RTCK, and voltage reference.
+That makes it the most complete JTAG adapter I have.
 ===== tricks =====
@@ Line 214: / Line 244: @@
 Warn : gdb services need one or more targets defined
 </code>
+''0x3ba00477'' corresponds to the Cortex-M3 TAP, and ''0x16410041'' to the boundary scan TAP, as documented in the [[http://www.st.com/web/en/resource/technical/document/reference_manual/CD00171190.pdf|STM32F1xx reference manual]].
 While the ST-Link v2 is mainly meant to be used as SWD adapter, it also supports JTAG. Both are implemented with the High Level Adapter (HLA) driver. But it seems scan chain is [[http://sourceforge.net/p/openocd/mailman/message/31038247/|not supported by the HLA]].